Enhance Nature's Beauty

every timber is unique and beautiful to the touch

Engineered for the harshest environments. Australia.

Equisol's unique formula protects your timber from mother nature's greatest forces. From the harshest tropical conditions to hail and snow, Equisol has you covered, giving you the best timber protection possible.

MoistureControl-IconORANGEBLACK

Technology that lets water get in and out again

Unique moisture control penetrant technology is the secret to how Equisol oil lets timber breathe.
Oil and water don't usually mix. This creates hassles in drying, especially as even dry timber can have a moisture content as high as 15%, and can leave uneven patches.

moisture-penetrants

Moisture also reduces traditional timber oil's effectiveness in penetrating down and providing consistent protection. Equisol's technology allows our stabilising oil to penetrate the water barrier and push deep into the timber, drying much faster. It also lets moisture rise back out of the timber as it evaporates, minimising the damage of trapped water.

CellularStability-IconORANGEBLACK

Stabilises Cell Structures

As water moves in and out of timber, it causes the cells to shrink and swell at uneven rates when they lose or gain moisture below their fibre saturation point.

These changes exert force on the cells' structural integrity as they move and push against each other, resulting in warping, twisting, cupping and finally splitting. Equisol provides dimensional stability at the cellular level by penetrating deeply and coating the cell walls, reducing moisture-related movement.

MouldResistant-IconORANGEBLACK

Mould and Algae Inhibitors

Equisol's environmentally-friendly linseed oil base is specially formulated with mould and algae inhibitors to help Equisol nourish and preserve timber. Enhanced UV absorbers also help control the effect of sunlight exposure.

The formulation increases rot resistance and helps stabilise timber's sugar content, which provides food for decay-causing moulds and fungi.

Nature can be a mother to your timber, don't let her

Timber is hygroscopic, meaning it absorbs water and sun in cycles of swelling and shrinking to balance with its surrounding environment. As moisture moves in and out, it attracts mould, bacteria, fungi and insect infestations if left untreated.
Most coatings attempt to keep water out, but water molecules are very small and eventually migrate through, creating a situation where water becomes trapped and failure is inevitable. The result is flaking, peeling coatings and damaged timber that must be heavily sanded back and possibly repaired before being re-coated.

If you've seen these signs, you have a problem.

icons-weather_Radiation

UV Radiation

Prolonged UX exposure attacks film coatings and the underlying timber, breaking down the surface cells of the timber. The attached coating then flakes off.

icons-weather_Moisture

Trapped Moisture

Water gets in through top coatings (and underneath if the underside is not treated correctly), leaving coatings brittle and cracking from trapped moisture, expansion and contraction.


icons-weather_Mould

Mould

Inferior decking oil or trapped moisture (especially in high humidity) allows mould spores to land, feed on the oil and grow, eventually turning your timber black.


icons-weather_Fungal_Decay

Fungal Decay

Moisture enters through unprotected sawn ends, establishing fungal decay and attracting insects.

icons-weather_Rust_Holes

Rust and Holes

Nail and screw holes allow moisture in, accelerating mould and rust.

icons-weather_Splitting

Splitting and Warping

Eventually the timber structure breaks down after continual shrinking and expanding with cycles of sun and water, requiring complete replacement.


For Complete Weather Control

icons-weather-boxes
icons-weather-boxes-mobile
timber-water-drops-cropped

Less mess, less work, longer life

Can be applied on new timber immediately without weathering? Yes No No
Can be applied on new timber without preparation? Yes No No
Can be wet stacked for easy pre-coating before construction? Yes No No
Number of coats required on new timber? Two Three Three
Single pack application needing only one product? Yes No No
Can be applied on days that are hot, sunny, humid or cold? Yes No No
Can be applied to damp timber? Yes No No
No marks from dirt or leaves on deck during application? Yes No No
No wet edge marks, even with minimum applying skill? Yes No No
Average coverage rate (sqm/litre)? 8-16 10-15 6-10
Curing time in days? Three Seven Seven
Does product ever blister, peel or crack? No Yes Yes
Scratch resistant and easily repaired? Yes No No
Reduces long term timber cupping, warping or splitting? Yes No No
Number of coats required for re-coating maintenance? One Two Two
No need to use paint stripper or heavy sanding for re-coat? Yes No No
Recommended maintenance required (months)? 6-12 12 3-6
Re-coats build a long term accumulative benefit? Yes No No

Equisol

Unit 2, 17 Bailey Crescent,
Southport, QLD 4215 Australia
1300 966 322
orders@equisol.pro

0