Less mess, less machine blockages and faster wet stacking

FastDryingFormula
IBC and 200L Equisol Rapid
FastDryingFormula

Equisol RAPID

Push through more pre-oiling in less time.
Equisol’s unique Rapid formula will speed up your pre-oiling process, with a better finish that penetrates into the timber, allowing moisture and heat to escape, whilst retaining the natural feel of wood. Formulated for the extreme Australian environments.

  • Unique Equisol Rapid formulation made for pre-oiling machines, based on our retail Pro E365 stabilising oil.
  • Can be wet stacked without sticking for easy pre-oiling before construction
  • Fast drying with no wet edge marks
  • No sediment or solids to clog machines
  • No surface crystallisation
  • Includes mouldicides and algaecides
  • Environmentally friendly modified linseed oil will not give timber a green hue.
  • Available in 20L, 200L and 1000L bulk containers
Clean up: Soapy water or turpentine
Sizes Available: 200L, 1000L
Protects Against

Directions for Use

USES: Pre-oiling formulation suitable for bare timber intended for exterior installation. Equisol Rapid may be applied to either rough sawn, dressed, pressure treated and unseasoned timber. Not recommended for use on interior timbers.

SURFACE PREPARATION: All surfaces must be free from oil, grease and other contaminants. Equisol Rapid is not recommended on timber where previous coating is present without stripping first.Remove all sanding dust before treating.

APPLICATION: Apply a single coat of Equisol Rapid using a pre-oiling machine, brush, spray or floor applicator. Multiple coats are not recommended, as Equisol Rapid will not penetrate timber, resulting in uneven surface colour and sheen.

NOTE: Equisol Rapid is designed as a pre-oiling formula to protect timber prior to, and during, exterior installation. It is not a final protective coat. A second coat of Equisol ProE365 is required for optimum timber protection. Once timber has been installed, clean all surfaces exposed to weather and foot traffic with Equisol Prime tannin and oil remover as per label instructions, before using Equisol Vitalise to neutralise the surface. Re-oil with Equisol ProE365 as per label instructions.

THINNING: Equisol Rapid does not require thinning.

DRYING TIME: Drying times are dependent on timber type, moisture and climate.

RECOAT: Leave for 24 hours if possible

WALK ON: 24 hours after recoat, or when dry.

COVERAGE: Coverage rate will vary depending on texture and absorbency of wood species to be used.
Softwood: 6-10m2 per litre.
Hardwood: 10-16m2 per litre.

CLEAN UP: Clean brushes and other equipment using soapy water or turpentine.

Safety Directions

May be harmful if swallowed and enters airways.

May cause allergic skin reaction. May cause drowsiness or dizziness. Keep out of reach of children. Read the label before opening or using. Keep away from all sources of ignition – NO smoking. Keep container tightly closed. Ground/bond container and receiving equipment. Use explosion-proof electrical, ventilating, lighting and all other equipment. Use only non-sparking tools. Take precautionary measures against static discharge.

Avoid breathing mist, vapours or spray. Use only outdoors or in well-ventilated are. Wear protective 
clothing, gloves, eye/face protection and suitable respirator as required. Contaminated work clothing should not be allowed out of the workplace. Wash contaminated clothing before re-use. Wash hands, face and all exposed skin thoroughly after handling. Store locked up. Store in a well ventilated place and away from oxidizing agents and foodstuffs. Keep cool. Do not empty into drains.

FIRST AID: If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 
13 11 26; New Zealand 0800 764 766). If medical advice is needed, have product container or label at hand.

SWALLOWED: If swallowed, rinse mouth. Do NOT induce vomiting. Give a glass of water. Immediately call a POISON CENTRE or doctor/physician.

EYE: If in eyes, hold eyes open, flush with running water for at least 15 minutes and see a doctor.

SKIN: If skin or hair contact occurs, immediately remove any contaminated clothing and wash skin and hair thoroughly with running water. If swelling, redness, blistering or irritation occurs seek medical assistance.

INHALED: Remove from contaminated area – avoid becoming a casualty. Allow patient to assume most comfortable position and keep warm. Apply artificial respiration if not breathing. Seek medical advice.

FOR FIRE: If involved in fire use alcohol resistant foam. If unavailable, use standard foam or dry agents. Avoid breathing product of combustion.

FOR SPILLS: Clear area of all unprotected personnel. Slippery when spilt. Wear protective equipment. Absorb with sand or soil. Collect and seal in properly labeled drums. Dispose of contents/containers in accordance with local, regional, national and international.

DISPOSAL: Do NOT pour leftover product down the drain. Keep unwanted product in sealed containers for disposal via special chemical waste collections. Dispose of contents/containers in accordance with local, regional, national and international regulations.

For further information or a copy of the Product Safety Data Sheet telephone Equisol on AUST 1300 966 322 or go to equisol.pro.

DO NOT REUSE CONTAINER. SEE THE SAFETY DATA SHEET FOR ADDITIONAL INFORMATION.
FOR EMERGENCIES call AUST 13 11 26.

pre-coating-water

Moisture gets in from underneath, beginning the decay process. Onsite coatings can\'t reach right around due to access limitations.

pre-coating-sun

Equisol stabilising oil is consistently applied on all four sides by machine, for an even thickness.

icon-circle-paint-edges

Expert TIP: To ensure your timber is protected all the way around, ends sawn on site should be oiled before installation.

Timber components can be pre-finished and assembled before installation
Screens, lattice, panels, fencing and sidings
Protects timber during construction and minimises staining
Timber in difficult access situations can be pre-oiled to reduce costs in labour and scaffolding
Saves time
Less trades on site
Reduces onsite labour costs by reducing the amount of work onsite
Reduces onsite issues and mess
Accelerates installation time as deck does not need to dry between work
Reduces number of top coats on site
More consistent oiling than possible by hand
Not reliant on the weather for onsite application
No sanding in between coats
Reduced hazard of slippery surfaces by reduced drying times
TIMBER PROTECTION
Protects timber close to ground susceptible to rotting due to high moisture content
Minimise blisters, cracks, peels and flakes
All four sides of timber are protected, minimising surface checking, cupping, warping and splitting
Improves dimensional stability by minimising absorption of moisture
Surfaces that cannot be reached by brush after installation are protected
Minimises water stains
Extends the service life of decking and retains the value of the asset
Colour Tone Dark Brown

Dark Brown

Colour Tone Red Brown

Red Brown

Colour Tone Black

Black

Colour Tone Medium Brown

Medium Brown

Colour Tone Pale Brown

Pale Brown

Colour Tone Grey

Grey

Choose Your Tone

Equisol Rapid is available pre-coloured in custom orders. Choose from 6 architect colours to maintain the natural timber colour character, delay silvering, and retain the “freshly oiled look” for longer.